<< Chapter < Page Chapter >> Page >

Problems

A wind turbine rotates at 20 rev/min. If its power output is 2.0 MW, what is the torque produced on the turbine from the wind?

τ = P ω = 2.0 × 10 6 W 2.1 rad / s = 9.5 × 10 5 N · m

Got questions? Get instant answers now!

A clay cylinder of radius 20 cm on a potter’s wheel spins at a constant rate of 10 rev/s. The potter applies a force of 10 N to the clay with his hands where the coefficient of friction is 0.1 between his hands and the clay. What is the power that the potter has to deliver to the wheel to keep it rotating at this constant rate?

Got questions? Get instant answers now!

A uniform cylindrical grindstone has a mass of 10 kg and a radius of 12 cm. (a) What is the rotational kinetic energy of the grindstone when it is rotating at 1.5 × 10 3 rev / min ? (b) After the grindstone’s motor is turned off, a knife blade is pressed against the outer edge of the grindstone with a perpendicular force of 5.0 N. The coefficient of kinetic friction between the grindstone and the blade is 0.80. Use the work energy theorem to determine how many turns the grindstone makes before it stops.

a. K = 888.50 J ;
b. Δ θ = 294.6 rev

Got questions? Get instant answers now!

A uniform disk of mass 500 kg and radius 0.25 m is mounted on frictionless bearings so it can rotate freely around a vertical axis through its center (see the following figure). A cord is wrapped around the rim of the disk and pulled with a force of 10 N. (a) How much work has the force done at the instant the disk has completed three revolutions, starting from rest? (b) Determine the torque due to the force, then calculate the work done by this torque at the instant the disk has completed three revolutions? (c) What is the angular velocity at that instant? (d) What is the power output of the force at that instant?

Figure shows a uniform disk that rotates around a vertical axis through its center. A cord is wrapped around the rim of the disk and pulled with a force of 10 N.
Got questions? Get instant answers now!

A propeller is accelerated from rest to an angular velocity of 1000 rev/min over a period of 6.0 seconds by a constant torque of 2.0 × 10 3 N · m . (a) What is the moment of inertia of the propeller? (b) What power is being provided to the propeller 3.0 s after it starts rotating?

a. I = 114.6 kg · m 2 ;
b. P = 104,700 W

Got questions? Get instant answers now!

A sphere of mass 1.0 kg and radius 0.5 m is attached to the end of a massless rod of length 3.0 m. The rod rotates about an axis that is at the opposite end of the sphere (see below). The system rotates horizontally about the axis at a constant 400 rev/min. After rotating at this angular speed in a vacuum, air resistance is introduced and provides a force 0.15 N on the sphere opposite to the direction of motion. What is the power provided by air resistance to the system 100.0 s after air resistance is introduced?

Figure shows a sphere attached to the end of a rod. The rod rotates about an axis that is at the opposite end of the sphere.
Got questions? Get instant answers now!

A uniform rod of length L and mass M is held vertically with one end resting on the floor as shown below. When the rod is released, it rotates around its lower end until it hits the floor. Assuming the lower end of the rod does not slip, what is the linear velocity of the upper end when it hits the floor?

Figure shows a uniform rod of length L and mass M is held vertically with one end resting on the floor. When the rod is released, it rotates around its lower end until it hits the floor.

v = L ω = 3 L g

Got questions? Get instant answers now!

An athlete in a gym applies a constant force of 50 N to the pedals of a bicycle to keep the rotation rate of the wheel at 10 rev/s. The length of the pedal arms is 30 cm. What is the power delivered to the bicycle by the athlete?

Got questions? Get instant answers now!

A 2-kg block on a frictionless inclined plane at 40 ° has a cord attached to a pulley of mass 1 kg and radius 20 cm (see the following figure). (a) What is the acceleration of the block down the plane? (b) What is the work done by the gravitational force to move the block 50 cm?

Figure shows a 2 kg block on an inclined plane at an angle of 40 degrees with a tether attached to a pulley of mass 1 kg and radius 20 cm.

a. a = 5.0 m / s 2 ; b. W = 1.25 N · m

Got questions? Get instant answers now!
Practice Key Terms 2

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, University physics volume 1. OpenStax CNX. Sep 19, 2016 Download for free at http://cnx.org/content/col12031/1.5
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'University physics volume 1' conversation and receive update notifications?

Ask
Michael Sag
Start Exam
Rachel Carlisle
Start Quiz
Marion Cabalfin
Start Quiz