<< Chapter < Page Chapter >> Page >
  • Explain the magnitude and direction of an induced eddy current, and the effect this will have on the object it is induced in.
  • Describe several applications of magnetic damping.

Eddy currents and magnetic damping

As discussed in Motional Emf , motional emf is induced when a conductor moves in a magnetic field or when a magnetic field moves relative to a conductor. If motional emf can cause a current loop in the conductor, we refer to that current as an eddy current    . Eddy currents can produce significant drag, called magnetic damping    , on the motion involved. Consider the apparatus shown in [link] , which swings a pendulum bob between the poles of a strong magnet. (This is another favorite physics lab activity.) If the bob is metal, there is significant drag on the bob as it enters and leaves the field, quickly damping the motion. If, however, the bob is a slotted metal plate, as shown in [link] (b), there is a much smaller effect due to the magnet. There is no discernible effect on a bob made of an insulator. Why is there drag in both directions, and are there any uses for magnetic drag?

The figure describes an experiment on exploring the effect of eddy currents. Part a of the figure shows a metal pendulum plate swinging between the pole pieces of a magnet. The pendulum is attached at one end to a pivot. Eddy currents are shown as small swirls on the surface of the plate. The oscillation is shown as damped by smaller displacement of the plate marked as S. Part b of the figure shows a slotted metal pendulum plate swinging between the pole pieces of a magnet. The pendulum is attached at one end to a pivot. Eddy currents are less effective. The oscillation is shown with a larger displacement of the plate marked as S, than the displacement in part a. Part c of the figure shows a non conducting pendulum plate swinging between the pole pieces of a magnet. The pendulum is attached at one end to a pivot. Extremely small currents are induced. The oscillation is shown with a larger displacement of the plate marked as S, than the displacement in part a.
A common physics demonstration device for exploring eddy currents and magnetic damping. (a) The motion of a metal pendulum bob swinging between the poles of a magnet is quickly damped by the action of eddy currents. (b) There is little effect on the motion of a slotted metal bob, implying that eddy currents are made less effective. (c) There is also no magnetic damping on a nonconducting bob, since the eddy currents are extremely small.

[link] shows what happens to the metal plate as it enters and leaves the magnetic field. In both cases, it experiences a force opposing its motion. As it enters from the left, flux increases, and so an eddy current is set up (Faraday’s law) in the counterclockwise direction (Lenz’s law), as shown. Only the right-hand side of the current loop is in the field, so that there is an unopposed force on it to the left (RHR-1). When the metal plate is completely inside the field, there is no eddy current if the field is uniform, since the flux remains constant in this region. But when the plate leaves the field on the right, flux decreases, causing an eddy current in the clockwise direction that, again, experiences a force to the left, further slowing the motion. A similar analysis of what happens when the plate swings from the right toward the left shows that its motion is also damped when entering and leaving the field.

The figure shows a more detailed description of a conducting plate attached to a pivot oscillating between the pole pieces of a magnet. A cross section is shown in the figure. The direction of magnetic field of the magnet is toward the plane of the paper. The direction of force, current and magnetic field at two extreme positions of the pendulum are marked. The direction of B is always into the paper. Based on the direction of force, the current direction of the pendulum at the two ends is marked as per the right hand rule. The eddy current on the plate is in anti clock wise direction in the left end and clock wise direction in the right end.
A more detailed look at the conducting plate passing between the poles of a magnet. As it enters and leaves the field, the change in flux produces an eddy current. Magnetic force on the current loop opposes the motion. There is no current and no magnetic drag when the plate is completely inside the uniform field.

When a slotted metal plate enters the field, as shown in [link] , an emf is induced by the change in flux, but it is less effective because the slots limit the size of the current loops. Moreover, adjacent loops have currents in opposite directions, and their effects cancel. When an insulating material is used, the eddy current is extremely small, and so magnetic damping on insulators is negligible. If eddy currents are to be avoided in conductors, then they can be slotted or constructed of thin layers of conducting material separated by insulating sheets.

Practice Key Terms 2

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, College physics ii. OpenStax CNX. Nov 29, 2012 Download for free at http://legacy.cnx.org/content/col11458/1.2
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'College physics ii' conversation and receive update notifications?

Ask