<< Chapter < Page Chapter >> Page >
Bit streams through digital communications receivers.

The receiver interested in the transmitted bit stream must perform two tasks when received waveform r t begins.

  • It must determine when bit boundaries occur: The receiver needs to synchronize with the transmitted signal. Because transmitter and receiver are designed inconcert, both use the same value for the bit interval T . Synchronization can occur because the transmitter begins sending with a reference bitsequence, known as the preamble . This reference bit sequence is usually the alternating sequenceas shown in the square wave example and in the FSK example . The receiver knows what the preamble bit sequence is and uses it to determine when bit boundariesoccur. This procedure amounts to what in digital hardware as self-clocking signaling : The receiver of a bit stream must derive the clock — when bit boundariesoccur — from its input signal. Because the receiver usually does not determine which bit was sent untilsynchronization occurs, it does not know when during the preamble it obtained synchronization. The transmittersignals the end of the preamble by switching to a second bit sequence. The second preamble phase informs the receiverthat data bits are about to come and that the preamble is almost over.
  • Once synchronized and data bits are transmitted, the receiver must then determine every T seconds what bit was transmitted during the previous bit interval. We focus on this aspect of thedigital receiver because this strategy is also used in synchronization.
The receiver for digital communication is known as a matched filter .

Optimal receiver structure

The optimal receiver structure for digital communication faced with additive white noise channels is the depicted matchedfilter.
This receiver, shown in [link] , multiplies the received signal by each of the possible membersof the transmitter signal set, integrates the product over the bit interval, and compares the results. Whichever path throughthe receiver yields the largest value corresponds to the receiver's decision as to what bit was sent during the previousbit interval. For the next bit interval, the multiplication and integration begins again, with the next bit decision made at theend of the bit interval. Mathematically, the received value of b n , which we label b ^ n , is given by
b ^ n i t n 1 T n T r t s i t
You may not have seen the i notation before. i · yields the maximum value of its argument with respect to the index i . i equals the value of the index that yields the maximum.Note that the precise numerical value of the integrator's output does not matter; what does matter is its value relative to theother integrator's output.

Let's assume a perfect channel for the moment: The received signal equals the transmitted one. If bit 0 were sent using thebaseband BPSK signal set, the integrator outputs would be

t n 1 T n T r t s 0 t A 2 T
t n 1 T n T r t s 1 t A 2 T If bit 1 were sent,
t n 1 T n T r t s 0 t A 2 T
t n 1 T n T r t s 1 t A 2 T

Can you develop a receiver for BPSK signal sets that requires only one multiplier-integrator combination?

In BPSK, the signals are negatives of each other: s 1 t s 0 t . Consequently, the output of each multiplier-integrator combination is the negative of theother. Choosing the largest therefore amounts to choosing which one is positive. We only need to calculate one ofthese. If it is positive, we are done. If it is negative, we choose the other signal.

Got questions? Get instant answers now!

What is the corresponding result when the amplitude-modulated BPSK signal set is used?

The matched filter outputs are ± A 2 T 2 because the sinusoid has less power than a pulse having the same amplitude.

Got questions? Get instant answers now!

Clearly, this receiver would always choose the bit correctly. Channel attenuation would not affect this correctness; it wouldonly make the values smaller, but all that matters is which is largest.

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play Download on the App Store Now




Source:  OpenStax, Fundamentals of electrical engineering i. OpenStax CNX. Aug 06, 2008 Download for free at http://legacy.cnx.org/content/col10040/1.9
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'Fundamentals of electrical engineering i' conversation and receive update notifications?

Ask