# 0.4 Lab 3-2 digital input and output with the msp430  (Page 2/2)

 Page 2 / 2

## So what?

In this lab we're going to use the MSP430's GPIO pins, combined with some external switches and an LED display, to build a basic I/O system for our board. Because of how things fit together on the board, it makes sense to use P1.0-P1.3 (the first three Port_1 GPIO Pins) to read the input switches and P1.4-P1.7 for the output signals.

## Outputs

Setting up the outputs is easy-- simply set the upper four bits (bits 4-7) of `&P1DIR` to "1", and then write the output to the upper four bits of `&P1OUT` . That means you'll have to shift your data left 4 positions before output, but you should already know a simple technique to do so!
You'll notice that when you change the output, the corresponding input bits also change. This happens because the input hardware always reads the status of the line, regardless if it is set to input our output. Changing the `&P1DIR` values only connects or disconnects the driving circuitry built into the MSP430. In advanced applications this can be used to analyze potential faults in the circuitry outside the chip.

## Inputs

Inputs are also "easy," but there are a few hardware concepts you'll need before you understand how they work!

## A little bit about wires

As mentioned briefly in class, binary digital logic has two valid states, plus one third mystery state. That third state, "The High Impedance State," (High-Z) just means that the wire isn't connected to anything. You've already talked about using so called tri-state buffers to negotiate who can talk on a shared bus-- the listening components enter the high impedance state, allowing the transmitting component's signal to drive the bus with no conflicts.

Impedance is a generalized form of the classical Resistance concept. Impedances can be real or complex valued, and apply too signals expressed in complex exponential form ( whether constant or variable! ). To learn more about impedance, check out Dr. Johnson's sections from the Elec 241 course notes.

In order to read useful input from your switches, you need them to be "0" in one state, and "1" in the other. Yet knowing what you know about the third state, the switch shown above will actually give a "0"/"1" (depending on what you connect it to) when closed and "High-Z" when open. Because there's nothing else driving the sensor input besides our switch, the input value will be random when the switch is open . In digital logic this is called floating, and it is a very very bad thing.

One simple solution is the Pull-Up (or Pull-Down) Resistor . Connecting the floating side of the switch to a logic level through a large resistor will tie down the floating input when the switch is open, but won't effect the read value much when the switch is closed.

## Pull-ups in the msp430

For better or for worse, the MSP430 actually has pull up resistors already built into the chip's hardware. Configuring them takes several steps, but once setup they provide all the functionality above without the extra external connections.
• Set the Pin Direction for P1.0-P1.3 to input. (Set bits 0-3 of `&P1DIR` to "0")
• Enable the resistors themselves. (Set bits 0-3 of `&P1REN` to "1")
• Configure the resistors to be pull-up. (Set bits 0-3 of `&P1OUT` to "1")
The most confusing part of the whole process is the double function of `P1OUT` . Because of the hardware implementation on the MSP430, `&P1OUT` controls the outputs as well as the connections to the pull up resistors. You will need to ensure that every time you output a value, you KEEP the lower four bits "1" . The easiest way to do this is just by ORing your raw output with the constant `#0Fh` before you write to `P1OUT` . The MSP430 does not have a specific "or" instruction by name, but `bis` does the same thing. For more info on `bis` and its inverse `bic` , see next week's lab.

## Philosophy

• A traditional single threaded polling scheme consists of a main loop that runs continuously. Within that loop, the processor periodically checks for changes, and if there are none, continues looping. Once a change is detected, the program moves to a new section of code or calls a new subroutine to deal with the changes.
• Polling has advantages and disadvantages-- it keeps program execution linear and is very easy to code and implement, but it also is not incredibly responsive. Since polling only checks values at certain points in the main run loop, if the loop is long or changes occur quickly, a polling scheme can miss input data. For now though it will suffice.

## Assignment details

Your task is to code a simple input to output echo program for the MSP430. Your program should consist of:

• A setup section that runs once and configures the GPIO pins
• A main loop that runs infinitely
• Code inside your loop to read the state of the GPIO input pins
• A separate section of code to write the changes to the output pins and then return to the main loop

You should already know the basics of masking from class, but it becomes very important when dealing with I/O. Since different pins do different things in the same port (P1), you the programmer will have to be careful not to accidentally modify the wrong bits even though your instructions will operate on the entire register.

All images drawn by Matt Johnson, Rice ECE

where we get a research paper on Nano chemistry....?
nanopartical of organic/inorganic / physical chemistry , pdf / thesis / review
Ali
what are the products of Nano chemistry?
There are lots of products of nano chemistry... Like nano coatings.....carbon fiber.. And lots of others..
learn
Even nanotechnology is pretty much all about chemistry... Its the chemistry on quantum or atomic level
learn
da
no nanotechnology is also a part of physics and maths it requires angle formulas and some pressure regarding concepts
Bhagvanji
hey
Giriraj
Preparation and Applications of Nanomaterial for Drug Delivery
revolt
da
Application of nanotechnology in medicine
what is variations in raman spectra for nanomaterials
ya I also want to know the raman spectra
Bhagvanji
I only see partial conversation and what's the question here!
what about nanotechnology for water purification
please someone correct me if I'm wrong but I think one can use nanoparticles, specially silver nanoparticles for water treatment.
Damian
yes that's correct
Professor
I think
Professor
Nasa has use it in the 60's, copper as water purification in the moon travel.
Alexandre
nanocopper obvius
Alexandre
what is the stm
is there industrial application of fullrenes. What is the method to prepare fullrene on large scale.?
Rafiq
industrial application...? mmm I think on the medical side as drug carrier, but you should go deeper on your research, I may be wrong
Damian
How we are making nano material?
what is a peer
What is meant by 'nano scale'?
What is STMs full form?
LITNING
scanning tunneling microscope
Sahil
how nano science is used for hydrophobicity
Santosh
Do u think that Graphene and Fullrene fiber can be used to make Air Plane body structure the lightest and strongest. Rafiq
Rafiq
what is differents between GO and RGO?
Mahi
what is simplest way to understand the applications of nano robots used to detect the cancer affected cell of human body.? How this robot is carried to required site of body cell.? what will be the carrier material and how can be detected that correct delivery of drug is done Rafiq
Rafiq
if virus is killing to make ARTIFICIAL DNA OF GRAPHENE FOR KILLED THE VIRUS .THIS IS OUR ASSUMPTION
Anam
analytical skills graphene is prepared to kill any type viruses .
Anam
Any one who tell me about Preparation and application of Nanomaterial for drug Delivery
Hafiz
what is Nano technology ?
write examples of Nano molecule?
Bob
The nanotechnology is as new science, to scale nanometric
brayan
nanotechnology is the study, desing, synthesis, manipulation and application of materials and functional systems through control of matter at nanoscale
Damian
Is there any normative that regulates the use of silver nanoparticles?
what king of growth are you checking .?
Renato
What fields keep nano created devices from performing or assimulating ? Magnetic fields ? Are do they assimilate ?
why we need to study biomolecules, molecular biology in nanotechnology?
?
Kyle
yes I'm doing my masters in nanotechnology, we are being studying all these domains as well..
why?
what school?
Kyle
biomolecules are e building blocks of every organics and inorganic materials.
Joe
Got questions? Join the online conversation and get instant answers!