<< Chapter < Page Chapter >> Page >
Setting the Sine Wave to 300 Hz

Make a note of the accuracy of the model.

Changing the frame sizes

Increase the Samples per frame to 1024 in both the “Sine Wave” and the “Random Source” Blocks.

Adjusting Frame Size for Sine Wave
Adjusting the Frame Size for the Random Source

Run the model again.

Question: How does this change to the frame size affect performance?

Setting the delay value

Click on the “Delay” Block. Change the number of Delay (samples) to 50.

Setting the Delay (samples)

Run the model again and make a note of the accuracy of the measurement.

Change Delay (samples) The Delay (samples) should be smaller than the frame size, otherwise the frames do not overlap. to 12 and run the model again.

Question: How does the value of delay (samples) affect the accuracy of the model?

Changing the amount of noise present

Reload the original model to restore the initial settings.

Change the amount of Gain to make the gain 0.10 (10% noise).

Changing the Amount of Noise Present

Run the model and make a note of the accuracy of the measurements. Repeat, but this time, use a gain of 0.01 (1% noise).

Question: Does the algorithm work better for high signal-to-noise ratios or for low signal-to-noise ratios? Make a note of the answer.

Changing the sampling frequency

Change the sample time in both the “Sine Wave” and the “Random Noise” blocks to 48000 Hz.

Changing the Sine Wave Sample Time
Changing the Random Source Sample Time

Run the model.

Question: Does the model produce better results with 8000Hz sampling or 48000 Hz sampling? Make a note of the answer.

The fully optimized simulation

You should now know what are the optimum parameters for the simulation.

Set these parameters and run the model.

Summary of simulation

You have now run the signal-to-noise ratio model and should be aware of the best settings for consistency of measurements, delay and sampling frequency.

You are now ready to go to the C6713 DSK Model.

Real-time model for ti c6713 dsk

Texas instruments c6713 dsk setup

Texas Instruments C6713 DSK Setup

Alternatively, you can use computer loudspeakers.

Starting code composer studio

There are several stages required in order to implement the Signal-to-Noise measurement. These are now described.

Starting up code composer studio

Start Code Composer Studio for C6713 DSK and use Debug ->Connect

Startup Screen for Code Composer Studio (CCS)

The texas instruments c6713 dsk model

You will now use the knowledge you have gained during the PC Simulation to produce an optimized version of this algorithm for use with the Texas Instruments C6713 DSK.

Opening the c6713 dsk model

Open the SignalToNoiseDSK6713.mdl.

The parent is shown in Figure 15.


Double click on the “function()” block.

Viewing the signal-to-noise measurement algorithm

The details of the C6713 Algorithm are shown in Figure 16.

Audio Noise Gate

Setting the sampling rate and frame size

Double-click on the “Mic In C6713 DSK ADC” block.

Set the Sampling rate (Hz) and Samples per frame fields to the best value you found while carrying out the Simulation. The values may be different to those written here.

Setting the Sampling Rate and Frame Size

Setting the delay size

Double-click on the “Delay” block. Set the Delay (samples) to the best value found during simulation. The value will not be 999!

Setting the Delay Size

Returning to the parent system

From the Toolbar, select the “Up Arrow” icon. This returns you to the next higher level.

Returning to the Parent System

Building the model

Selecting real-time workshop

Select Tools ->Real-Time Workshop ->Build Model.

Building the Model

The completed model running on code composer studio

From the folders on the left, select the source code for the project.

The Completed Model Running in Code Composer Studio

Different settings on the c6713 dsk

Microphone straight through to loudspeakers

To check out the microphone and loudspeakers, set the DIP switches on the C6713 DSK as follows:

Switch Position 0

The microphone is fed directly to the loudspeakers. There is no noise gate.

Switch position for the audio noise gate

To run the Audio Noise Gate, set the DIP switch to 1.

Switch Position 1 for Audio Noise Gate

Note that when you are not speaking, there is no audio output at all – just silence.

Modifying the model

The next stage is to modify the model. You can change the smoothing filter. If the filter is too long, the delay will be noticeable.

Changing the filter type

Double-click on the “Lowpass” block. Change the Order to a value other than 10.

Changing the Number of Filter Elements

Re-building the model

Select Tools ->Real-Time Workshop ->Build Model.

Re-building the Model

Running the updated model

Run the updated model and listen to the effect on the audio noise gate.

Some things to try

You may wish to experiment with different settings. Here are some suggestions.

Add an input filter

While running the Simulation, you will have noticed that the Signal-to-Noise Algorithm works better on some frequencies than others.

Add the appropriate filter to select only the frequencies where the algorithm works well.

Process stereo inputs

Change the input from “Microphone” to “Stereo Line Input”.

Add a second channel to make the processing stereo.

Best signal selection

When stage 3.2 has been completed, modify the model so that the output is the better of the two stereo inputs.

MATLAB and Simulink are registered trademarks of The MathWorks, Inc. See www.mathworks.com/trademarks for a list of additional trademarks. Other product or brand names may be trademarks or registered trademarks of their respective holders.

Questions & Answers

where we get a research paper on Nano chemistry....?
Maira Reply
nanopartical of organic/inorganic / physical chemistry , pdf / thesis / review
what are the products of Nano chemistry?
Maira Reply
There are lots of products of nano chemistry... Like nano coatings.....carbon fiber.. And lots of others..
Even nanotechnology is pretty much all about chemistry... Its the chemistry on quantum or atomic level
no nanotechnology is also a part of physics and maths it requires angle formulas and some pressure regarding concepts
Preparation and Applications of Nanomaterial for Drug Delivery
Hafiz Reply
Application of nanotechnology in medicine
what is variations in raman spectra for nanomaterials
Jyoti Reply
ya I also want to know the raman spectra
I only see partial conversation and what's the question here!
Crow Reply
what about nanotechnology for water purification
RAW Reply
please someone correct me if I'm wrong but I think one can use nanoparticles, specially silver nanoparticles for water treatment.
yes that's correct
I think
Nasa has use it in the 60's, copper as water purification in the moon travel.
nanocopper obvius
what is the stm
Brian Reply
is there industrial application of fullrenes. What is the method to prepare fullrene on large scale.?
industrial application...? mmm I think on the medical side as drug carrier, but you should go deeper on your research, I may be wrong
How we are making nano material?
what is a peer
What is meant by 'nano scale'?
What is STMs full form?
scanning tunneling microscope
how nano science is used for hydrophobicity
Do u think that Graphene and Fullrene fiber can be used to make Air Plane body structure the lightest and strongest. Rafiq
what is differents between GO and RGO?
what is simplest way to understand the applications of nano robots used to detect the cancer affected cell of human body.? How this robot is carried to required site of body cell.? what will be the carrier material and how can be detected that correct delivery of drug is done Rafiq
analytical skills graphene is prepared to kill any type viruses .
Any one who tell me about Preparation and application of Nanomaterial for drug Delivery
what is Nano technology ?
Bob Reply
write examples of Nano molecule?
The nanotechnology is as new science, to scale nanometric
nanotechnology is the study, desing, synthesis, manipulation and application of materials and functional systems through control of matter at nanoscale
Is there any normative that regulates the use of silver nanoparticles?
Damian Reply
what king of growth are you checking .?
What fields keep nano created devices from performing or assimulating ? Magnetic fields ? Are do they assimilate ?
Stoney Reply
why we need to study biomolecules, molecular biology in nanotechnology?
Adin Reply
yes I'm doing my masters in nanotechnology, we are being studying all these domains as well..
what school?
biomolecules are e building blocks of every organics and inorganic materials.
how did you get the value of 2000N.What calculations are needed to arrive at it
Smarajit Reply
Privacy Information Security Software Version 1.1a
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get Jobilize Job Search Mobile App in your pocket Now!

Get it on Google Play

Source:  OpenStax, From matlab and simulink to real-time with ti dsp's. OpenStax CNX. Jun 08, 2009 Download for free at http://cnx.org/content/col10713/1.1
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'From matlab and simulink to real-time with ti dsp's' conversation and receive update notifications?