<< Chapter < Page Chapter >> Page >

Buffer sizes

In the program file is a macro that is used to define the size of the buffers that are in the inStream and outStream buffers. The macro is

#define CHANLEN 256 // Number of samples per channel

The CCS project uses TI's device drivers described in SPRA846. In the TI document SPRA846 it states that "If buffers are placed in external memory for use with this device driver they should be aligned to a 128 bytes boundary. In addition the buffers should be of a size multiple of 128 bytes as well for the cache to work optimally." If the SIO streams inStream and outStream are in external memory then the buffer sizes need to adhere to this requirement. If the streams are placed in internal memory then they can be any size desired as long as there is enough memory.

Suppose you want to keep the buffers in external memory but change the size. As an example, you want to change the length of each channel to 512 (multiple of 128). Then change CHANLEN to 512 and then open the configuration file DSK6713_audio.tcf and examine the properties for inStream .

DSP/BIOS SIO object inStream properties

Notice that the buffer size is 1024. This was for a channel length of 256. In the C6713 a Minimum Addressable Data Unit (MADU) is an 8-bit byte. The buffer size is in MADUs. Since each sample from the codec is 16-bits (2 MADUs) and there is a right channel and a left channel, the channel length is multiplied by 4 to get the total buffer size needed in MADUs. 256*4 = 1024. If you want to change the channel length to 512 then the buffer size needs to be 512*4 = 2048. Simply change the buffer size entry to 2048. Leave the alignment on 128. The same change must be made to the outStream object so that the buffers have the same size so change the buffer size in the properties for the outStream object also.

Suppose you have an algorithm that processes a block of data at a time and the buffer size is not a multiple of 128. To make the processing easier, you could make the stream buffer sizes the size you need for your algorithm. In this case, the stream objects must be placed in internal memory. As an example suppose you want a channel length of 94. Set the CHANLEN macro to 94 and then open the configuration file DSK6713_audio.tcf and examine and modify the properties for inStream and outStream . The buffer size will now be 94*4 = 376 and the buffer memory segment must be change from external RAM (SDRAM) to the internal RAM (IRAM).

DSP/BIOS SIO object inStream properties showing IRAM

Chip support library

CCS v3.3 comes with the chip support library (CSL). If for some reason you don't have it or it needs to be updated, download it from the TI website and install it.

Project setup

Make an empty dsp/bios project

To create a CCS project select Project->New… . This will bring up a window where you can enter the name of the project. The location selected is the default location for project files. Note that it is in the install directory for CCS v3.3. Select the Target type as TMS320C67xx . Press Finish .

CCS Project name and location

Copy files from the zip file to project directory. When they are copied to the project directory the files need to be added to the project. Right click on the project name and select Add Files To Project… . There should be 4 files added to the project as well as a header file and a couple of automatically generated files.

Project view after adding files

Set up the csl

Some options in the project need to be changed in order to use the CSL. To get to the project properties select Project->Build Options . Under Preprocessor enter the chip that we are using, in this case CHIP_6713 .

Preprocessor setting for CSL

The library file for the CSL also needs to be added to the project. Right click on the project or where it says Libraries and search for the CSL library file named csl6713.lib . It should be located in the directory C:\CCStudio_v3.3\C6000\csl\lib .

Add command file

The configuration file, DSK6713_audio.tcf , generates several files, one of them being a command file titled DSK6713_audio.cmd . Add this file to the project. If it is not there, you may need to attempt to build the project so that the file gets generated.

Using ccs with the dsk

Startup ccs with dsk connected to pc

After installing CCS v3.3 the C6713 DSK drivers need to be installed also. If they are not already installed then download them from Spectrum Digital, manufacturer of the DSK, or install them from the install disk that comes with the DSK.

Add power to the DSK board and then plug the USB connector into the PC you are using. Start up CCS. As the splash screen comes, under Windows XP, there should be a little window that pops up in the bottom right corner of the screen.

Popup window when CCS starts and DSK is connected

Connect to target

CCS v3.3 must first be connected to the target before the executable can be loaded onto the board. Select Debug->Connect . This will cause CCS to connect to the board and the board status should be in the lower left corner of the CCS window.

Target status

Debug/test the project

In order to debug and run the program you need to build it and then load it onto the DSK board. To build the project, click the Incremental Build button.

Incremental Build button

After the project builds successfully, load the .out file to the DSK board but selecting File->Load Program... and selecting the file. Or, if you want it loaded automatically, select Options- >Customize and then on the Project/Program/CIO tab select the checkmark next to Load Program After Build . When you load the program you will see a status window like the following figure.

Load Program status window

Once the program is loaded it is ready to be used. The following figure shows the final project with the main program file.

Final project view

Questions & Answers

where we get a research paper on Nano chemistry....?
Maira Reply
what are the products of Nano chemistry?
Maira Reply
There are lots of products of nano chemistry... Like nano coatings.....carbon fiber.. And lots of others..
learn
Even nanotechnology is pretty much all about chemistry... Its the chemistry on quantum or atomic level
learn
Google
da
no nanotechnology is also a part of physics and maths it requires angle formulas and some pressure regarding concepts
Bhagvanji
Preparation and Applications of Nanomaterial for Drug Delivery
Hafiz Reply
revolt
da
Application of nanotechnology in medicine
what is variations in raman spectra for nanomaterials
Jyoti Reply
I only see partial conversation and what's the question here!
Crow Reply
what about nanotechnology for water purification
RAW Reply
please someone correct me if I'm wrong but I think one can use nanoparticles, specially silver nanoparticles for water treatment.
Damian
yes that's correct
Professor
I think
Professor
Nasa has use it in the 60's, copper as water purification in the moon travel.
Alexandre
nanocopper obvius
Alexandre
what is the stm
Brian Reply
is there industrial application of fullrenes. What is the method to prepare fullrene on large scale.?
Rafiq
industrial application...? mmm I think on the medical side as drug carrier, but you should go deeper on your research, I may be wrong
Damian
How we are making nano material?
LITNING Reply
what is a peer
LITNING Reply
What is meant by 'nano scale'?
LITNING Reply
What is STMs full form?
LITNING
scanning tunneling microscope
Sahil
how nano science is used for hydrophobicity
Santosh
Do u think that Graphene and Fullrene fiber can be used to make Air Plane body structure the lightest and strongest. Rafiq
Rafiq
what is differents between GO and RGO?
Mahi
what is simplest way to understand the applications of nano robots used to detect the cancer affected cell of human body.? How this robot is carried to required site of body cell.? what will be the carrier material and how can be detected that correct delivery of drug is done Rafiq
Rafiq
if virus is killing to make ARTIFICIAL DNA OF GRAPHENE FOR KILLED THE VIRUS .THIS IS OUR ASSUMPTION
Anam
analytical skills graphene is prepared to kill any type viruses .
Anam
Any one who tell me about Preparation and application of Nanomaterial for drug Delivery
Hafiz
what is Nano technology ?
Bob Reply
write examples of Nano molecule?
Bob
The nanotechnology is as new science, to scale nanometric
brayan
nanotechnology is the study, desing, synthesis, manipulation and application of materials and functional systems through control of matter at nanoscale
Damian
Is there any normative that regulates the use of silver nanoparticles?
Damian Reply
what king of growth are you checking .?
Renato
What fields keep nano created devices from performing or assimulating ? Magnetic fields ? Are do they assimilate ?
Stoney Reply
why we need to study biomolecules, molecular biology in nanotechnology?
Adin Reply
?
Kyle
yes I'm doing my masters in nanotechnology, we are being studying all these domains as well..
Adin
why?
Adin
what school?
Kyle
biomolecules are e building blocks of every organics and inorganic materials.
Joe
Got questions? Join the online conversation and get instant answers!
Jobilize.com Reply

Get the best Algebra and trigonometry course in your pocket!





Source:  OpenStax, Dsp lab with ti c6x dsp and c6713 dsk. OpenStax CNX. Feb 18, 2013 Download for free at http://cnx.org/content/col11264/1.6
Google Play and the Google Play logo are trademarks of Google Inc.

Notification Switch

Would you like to follow the 'Dsp lab with ti c6x dsp and c6713 dsk' conversation and receive update notifications?

Ask